POWER POND

Power towers use an array of flat, movable mirrors (called heliostats) to focus the sun's rays upon a collector tower (the target). The high energy at this point of concentrated sunlight is transferred to a working fluid for conversion to electrical energy in a heat engine, or in some instances, stored for nighttime usage, in order to provide a more continuous output.Parabolic troughsParabolic troughA long row of parabolic mirrors concentrates sunlight on a tube filled with a heat transfer fluid (usually oil). As with the power tower, this heated oil is used to power a conventional steam turbine, or stored for nighttime use. The largest operating solar power plant, as of 2007, is one of the SEGS parabolic trough systems in the Mojave Desert in California, USA (see Solar power plants in the Mojave Desert).Concentrating collector with steam engineSolar energy converted to heat in a concentrating collector can be used to boil water into steam (as is done in nuclear and coal power plants) to drive a steam engine or steam turbine. The concentrating collector can be a trough collector, parabolic collector, or power tower.
A parabolic solar collector concentrating the sun's rays on the heating element of a Stirling engine. The entire unit acts as a solar tracker.Solar energy converted to heat in a concentrating (dish or trough parabolic) collector can be used to drive a Stirling engine, a type of heat engine which uses a sealed working gas (i.e. a closed cycle) and does not require a water supply.Until recently, a solar Stirling system held the record for converting solar energy into electricity (30% at 1,000 watts per square meter). Such concentrating systems produce little or no power in overcast conditions and incorporate a solar tracker to point the device directly at the sun. That record has been broken by a so-called concentrator solar cell produced by Boeing-Spectrolab which claims a conversion efficiency of 40.7 percent.

SOLAR CHEMICAL

Solar chemical is any process that harnesses solar energy by absorbing sunlight and using it to drive an endothermic or photoelectrochemical chemical reaction Prototypes, but no large-scale systems, have been constructed.One approach has been to use conventional solar thermal collectors to drive chemical dissociation reactions. Ammonia can be separated into nitrogen and hydrogen at high temperature and with the aid of a catalyst, stored indefinitely, then recombined later to release the heat stored. A prototype system was constructed at the Australian National University].Another approach is to use focused sunlight to provide the energy needed to split water via photoelectrolysis into its constituent hydrogen and oxygen in the presence of a metallic catalyst such as zinc. Other research in this area has focused on semiconductors, and on the use of examined transition metal compounds, in particular titanium, niobium and tantalum oxides Unfortunately, these materials exhibit very low efficiencies, because they require ultraviolet light to drive the photoelectrolysis of water. Current materials also require an electrical voltage bias for the hydrogen and oxygen gas to evolve from the surface, another disadvantage. Current research is focusing on the development of materials capable of the same water splitting reaction using lower energy visible light.Solar thermal energy also has the potential to be used directly to drive chemical processes that require significant amounts of process heat, including at high temperatures that can be otherwise quite hard to attain.

Solar-Chemical

Solar chemical is any process that harnesses solar energy by absorbing sunlight and using it to drive an endothermic or photoelectrochemical chemical reaction Prototypes, but no large-scale systems, have been constructed.One approach has been to use conventional solar thermal collectors to drive chemical dissociation reactions. Ammonia can be separated into nitrogen and hydrogen at high temperature and with the aid of a catalyst, stored indefinitely, then recombined later to release the heat stored. A prototype system was constructed at the Australian National University].Another approach is to use focused sunlight to provide the energy needed to split water via photoelectrolysis into its constituent hydrogen and oxygen in the presence of a metallic catalyst such as zinc. Other research in this area has focused on semiconductors, and on the use of examined transition metal compounds, in particular titanium, niobium and tantalum oxides Unfortunately, these materials exhibit very low efficiencies, because they require ultraviolet light to drive the photoelectrolysis of water. Current materials also require an electrical voltage bias for the hydrogen and oxygen gas to evolve from the surface, another disadvantage. Current research is focusing on the development of materials capable of the same water splitting reaction using lower energy visible light.Solar thermal energy also has the potential to be used directly to drive chemical processes that require significant amounts of process heat, including at high temperatures that can be otherwise quite hard to attain.

POWER TOWER

Power towers use an array of flat, movable mirrors (called heliostats) to focus the sun's rays upon a collector tower (the target). The high energy at this point of concentrated sunlight is transferred to a working fluid for conversion to electrical energy in a heat engine, or in some instances, stored for nighttime usage, in order to provide a more continuous output.Parabolic troughsParabolic troughA long row of parabolic mirrors concentrates sunlight on a tube filled with a heat transfer fluid (usually oil). As with the power tower, this heated oil is used to power a conventional steam turbine, or stored for nighttime use. The largest operating solar power plant, as of 2007, is one of the SEGS parabolic trough systems in the Mojave Desert in California, USA (see Solar power plants in the Mojave Desert).Concentrating collector with steam engineSolar energy converted to heat in a concentrating collector can be used to boil water into steam (as is done in nuclear and coal power plants) to drive a steam engine or steam turbine. The concentrating collector can be a trough collector, parabolic collector, or power tower.
A parabolic solar collector concentrating the sun's rays on the heating element of a Stirling engine. The entire unit acts as a solar tracker.Solar energy converted to heat in a concentrating (dish or trough parabolic) collector can be used to drive a Stirling engine, a type of heat engine which uses a sealed working gas (i.e. a closed cycle) and does not require a water supply.Until recently, a solar Stirling system held the record for converting solar energy into electricity (30% at 1,000 watts per square meter). Such concentrating systems produce little or no power in overcast conditions and incorporate a solar tracker to point the device directly at the sun. That record has been broken by a so-called concentrator solar cell produced by Boeing-Spectrolab which claims a conversion efficiency of 40.7 percent.

Manufacture

The semiconductors of the periodic table of the chemical elements were identified as the most likely materials for a solid state vacuum tube by researchers like William Shockley at Bell Laboratories starting in the 1930s. Starting with copper oxide, proceeding to germanium, then silicon, the materials were systematically studied in the 1940s and 1950s. Today, silicon monocrystals are the main substrate used for integrated circuits (ICs) although some III-V compounds of the periodic table such as gallium arsenide are used for specialised applications like LEDs, lasers, solar cells and the highest-speed integrated circuits. It took decades to perfect methods of creating crystals without defects in the crystalline structure of the semiconducting material.
Semiconductor ICs are fabricated in a layer process which includes these key process steps:
Imaging Deposition Etching The main process steps are supplemented by doping, cleaning and planarisation steps.
Mono-crystal silicon wafers (or for special applications, silicon on sapphire or gallium arsenide wafers) are used as the substrate. Photolithography is used to mark different areas of the substrate to be doped or to have polysilicon, insulators or metal (typically aluminium) tracks deposited on them.
Integrated circuits are composed of many ovelapping layers, each defined by photolithography, and normally shown in different colors. Some layers mark where various dopants are diffused into the substrate (called diffusion layers), some define where additional ions are implanted (implant layers), some define the conductors (polysilicon or metal layers), and some define the connections between the conducting layers (via or contact layers). All components are constructed from a specific combination of these layers. In a self-aligned CMOS process, a transistor is formed wherever the gate layer (polysilicon or metal) crosses a diffusion layer. Resistive structures, meandering stripes of varying lengths, form the loads on the circuit. The ratio of the length of the resistive structure to its width, combined with its sheet resistivity determines the resistance. Capacitive structures, in form very much like the parallel conducting plates of a traditional electrical capacitor, are formed according to the area of the "plates", with insulating material between the plates. Owing to limitations in size, only very small capacitances can be created on an IC. More rarely, inductive structures can be built as tiny on-chip coils, or simulated by gyrators.

Integrated

Among the most advanced integrated circuits are the microprocessors or "cores", which control everything from computers to cellular phones to digital microwave ovens. Digital memory chips and ASICs are examples of other families of integrated circuits that are important to the modern information society. While cost of designing and developing a complex integrated circuit is quite high, when spread across typically millions of production units the individual IC cost is minimized. The performance of ICs is high because the small size allows short traces which in turn allows low power logic (such as CMOS) to be used at fast switching speeds.
ICs have consistently migrated to smaller feature sizes over the years, allowing more circuitry to be packed on each chip. This increased capacity per unit area can be used to decrease cost and/or increase functionality—see Moore's law which, in its modern interpretation, states that the number of transistors in an integrated circuit doubles every two years. In general, as the feature size shrinks, almost everything improves—the cost per unit and the switching power consumption go down, and the speed goes up. However, ICs with nanometer-scale devices are not without their problems, principal among which is leakage current (see subthreshold leakage and MOSFET for a discussion of this), although these problems are not insurmountable and will likely be solved or at least ameliorated by the introduction of high-k dielectrics. Since these speed and power consumption gains are apparent to the end user, there is fierce competition among the manufacturers to use finer geometries. This process, and the expected progress over the next few years, is well described by the International Technology Roadmap for Semiconductors (ITRS).